Search by VIN, make, model, vehicle type, unit name, or by article number of any oil:
Oil for Dacia - Jogger, RJI / RJX - 1.5 2WD (K9K) (110 hp) (81 kW)
Dacia Jogger, RJI / RJX 1.5 2WD (K9K) (110 hp) (81 kW), year of issue from 2021 - Engine oil, automatic transmission, transmission oil, antifreeze, brake fluid, power steering fluid (power steering) and other fluids.
K9K
For engine
RAVENOL HDS Hydrocrack Diesel Specific 5W-30 is based on additives with reduced ash content for use in modern passenger car with diesel engines with excellent cold start characteristics, low oil consumption and reduced pollutant emissions. This oil will increase the DPF and TWC life. HTHS- Viscosity >3.5 mPa*s (cP). Developed for fuel economy and energy conserving in EURO VI, EURO V and EURO IV Standard engines with normal and extended oil change intervals (until 50.000 km or 2 years possible).
Manufacturer Approved:
MB-Approval 226.51, Renault RN 0720
Compliance with the requirements:
Fiat 9.55535-S4
- Available packaging
- Product parameters
Volume:
60 L
vendor code:
1111121-060
Volume:
208 L
vendor code:
1111121-208
Volume:
1000 L
vendor code:
1111121-700
RAVENOL HDS Hydrocrack Diesel Specific 5W-30 is based on additives with reduced ash content for use in modern passenger car with diesel engines with excellent cold start characteristics, low oil consumption and reduced pollutant emissions. This oil will increase the DPF and TWC life. HTHS- Viscosity >3.5 mPa*s (cP). Developed for fuel economy and energy conserving in EURO VI, EURO V and EURO IV Standard engines with normal and extended oil change intervals (until 50.000 km or 2 years possible).
RAVENOL HDS Hydrocrack Diesel Specific 5W-30 achieves a high viscosity index through its formulation with special base oils. The excellent cold start behaviour provides an optimum lubricating safety during the cold run phase.
Because of a considerable fuel saving RAVENOL HDS Hydrocrack Diesel Specific 5W-30 contributes to protect the environment by reducing the emissions.
RAVENOL HDS Hydrocrack Diesel Specific 5W-30 minimizes friction, wear and fuel consumption with excellent cold start characteristics.
Suitable for extended oil change intervals where recommended by manufacturer.
Application instructions
RAVENOL HDS Hydrocrack Diesel Specific 5W-30 is an universal fuel economy engine oil for modern diesel engines with and without turbo charger in passenger cars and vans with extended oil change intervals. Extend the lifespan of the particle filter.
Due to the specific composition is RAVENOL HDS Hydrocrack Diesel Specific 5W-30 excellent suitable for use for several of the latest OEM requirements.
Characteristics
- Fuel economy in part and full power operation
- Excellent wear protection and high viscosity index also under high-speed driving conditions, the long life of the engine
- Excellent cold starting characteristics also at low temperatures below -30°C
- A safe lubricant film at high operating temperatures
- Low evaporative tendency, so lower oil consumption
- No deposits in combustion chambers, in the piston ring zone and valves because of oil conditioned
- Neutrality towards sealing materials
- Extended oil change intervals to protect natural resources
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
||
| SAE | 5W-30 |
5W-30
|
||
| Type | Synthetic |
Synthetic
|
||
| ACEA | C4 |
C4
|
||
| Manufacturer Approved | MB-Approval 226.51, Renault RN 0720 |
MB-Approval 226.51, Renault RN 0720
|
||
| Recomendations | Fiat 9.55535-S4 |
Fiat 9.55535-S4
|
||
| Density at 20 °C | g/cm³ | 843 | EN ISO 12185 |
843
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 12.1 | DIN 51562-1 |
12.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 72 | DIN 51562-1 |
72
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 166 | DIN ISO 2909 |
166
DIN ISO 2909
|
|
| HTHS Viscosity at 150 °C | mPa*s | 3.6 | ASTM D5481 |
3.6
mPa*s
ASTM D5481
|
| CCS Viscosity at -30 °C | mPa*s | 5500 | ASTM D5293 |
5500
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -35 °C | mPa*s | 19.100 | ASTM D4684 |
19.100
mPa*s
ASTM D4684
|
| Pourpoint | °C | -39 | DIN ISO 3016 |
-39
°C
DIN ISO 3016
|
| Noack Volatility | % | 7.6 | ASTM D5800 |
7.6
%
ASTM D5800
|
| Flashpoint | °C | 236 | DIN EN ISO 2592 |
236
°C
DIN EN ISO 2592
|
| tbn | mgKOH/g | 7.9 | ASTM D2896 |
7.9
mgKOH/g
ASTM D2896
|
| Sulphated Ash | %wt. | 0.49 | DIN 51575 |
0.49
%wt.
DIN 51575
|
| Approvals | Fiat 9.55535-S4, MB 226.51, Renault RN0720 |
Fiat 9.55535-S4, MB 226.51, Renault RN0720
|
RAVENOL Professional Engine Cleaner is active concentrate for longer oil cleanliness for all petrol and diesel engines (with and without catalytic converter).
- Available packaging
- Product parameters
RAVENOL Professional Engine Cleaner can also be used in motorcycles.
RAVENOL Professional Engine Cleaner effectively breaks down dirt accumulation and sludge deposits in the engine compartment using intensive-cleaning tensides and removes these effectively when draining used oil.
RAVENOL Professional Engine Cleaner cleans and rinses the entire engine system.
Application Note
RAVENOL Professional Engine Cleaner is added to the warm motor oil.
Area of application:
-If black sludge is suspected
-In the event of hydraulic tappets rattling
-In the event of delayed oil change
-For soiled engines or used oil
-Preventively at every oil change to avoid contamination of the engine
-Also suitable for oldtimers
Dosage: 300 ml RAVENOL Professional Engine Cleaner are sufficient for one application of approx. 5L Oil, regardless of manufacturer and motor size.
Application: Add the contents to the warm motor oil before changing oil. Do not go below the minimum oil level. For maximum effect, allow to run for up to 10 minutes. Afterwards, immediately replace oil and filter.
RAVENOL Professional Engine Cleaner is tried and tested for aggregates with motor oils based on mineraloil and synthetic oil.
Characteristics
- Long-term effectiveness and clean fresh oil
- Remedy for soiled engines
- Protection against compression loss in the area of the piston rings
- Leads to better exhaust emissions and increases the performance of the engine
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Viscosity at 40 °C | mm²/s | 5 | DIN EN ISO 3104 |
5
mm²/s
DIN EN ISO 3104
|
| Density at 15°C | kg/m³ | 0 | EN ISO 12185 |
0
kg/m³
EN ISO 12185
|
| Flashpoint (PM) | °C | 132 | DIN EN ISO 2592 |
132
°C
DIN EN ISO 2592
|
| Pourpoint | °C | -30 | DIN ISO 3016 |
-30
°C
DIN ISO 3016
|
| Color | Yellow | visual |
Yellow
visual
|
JR5
RAVENOL Getriebeoel PSA 75W-80
For transmission
RAVENOL Getriebeoel PSA SAE 75W-80 has a special formula for outstanding wear protection and lubrication properties.
Compliance with the requirements:
PSA B71 2315
SAE: 75W-80
API: GL-4
Equivalents OEM:
GM 1940711, GM 9163335, Nissan 999MPMTF20P, Nissan KE91600Q40, Nissan KE91699012, Nissan KE91699012, Nissan KE91699033, Nissan KE91699071R, Nissan KE9169903301, Nissan KLD9275801, Peugeot 9730AG, Peugeot 1615100080, Peugeot 1618078480, Peugeot 1635055880, PSA 9730A2, PSA 9730AA, PSA 973641, Renault 7711143534
- Available packaging
- Product parameters
Volume:
1 L
vendor code:
1222100-001
Code:
4014835734111
Volume:
4 L
vendor code:
1222100-004
Code:
4014835734197
Volume:
10 L
vendor code:
1222100-010
Code:
4014835734142
Volume:
20 L
vendor code:
1222100-020
Volume:
20 L, ecobox
vendor code:
1222100-B20
Code:
4014835788824
Volume:
60 L
vendor code:
1222100-060
Volume:
60 L, print
vendor code:
1222100-D60
Volume:
208 L
vendor code:
1222100-208
Volume:
208 L, print
vendor code:
1222100-D28
Volume:
1000 L
vendor code:
1222100-700
RAVENOL Getriebeoel PSA SAE 75W-80 has a special formula for outstanding wear protection and lubrication properties.
Application instructions
RAVENOL Getriebeoel PSA SAE 75W-80 is used in manual shift transmissions requiring trouble-free lubrication.
RAVENOL Getriebeoel PSA SAE 75W-80 can be used in manual transmissions where the manufacturer specifies a low-viscosity oil.
Characteristics
- Outstanding oxidation protection.
- Low viscosity in low temperatures.
- Excellent wear protection.
- Enhanced EP properties.
- Good foaming properties.
- Neutral to sealants.
- Outstanding protection from rust and corrosion.
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Recommendations | PSA B71 2315 |
PSA B71 2315
|
||
| Brand | RAVENOL |
RAVENOL
|
||
| SAE | 75W-80 |
75W-80
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | GL-4 |
GL-4
|
||
| Recomendations | PSA B71 2315 |
PSA B71 2315
|
||
| Density at 20 °C | g/cm³ | 843 | EN ISO 12185 |
843
g/cm³
EN ISO 12185
|
| Color | light yellow | visual |
light yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 8.5 | DIN 51562-1 |
8.5
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 43.1 | DIN 51562-1 |
43.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 178 | DIN ISO 2909 |
178
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 52.500 | ASTM D2983 |
52.500
mPa*s
ASTM D2983
|
| Pourpoint | °C | -39 | DIN ISO 3016 |
-39
°C
DIN ISO 3016
|
| Flashpoint | °C | 234 | DIN EN ISO 2592 |
234
°C
DIN EN ISO 2592
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | PSA B71 2315 |
PSA B71 2315
|
DOT 4 LV
- Available packaging
- Product parameters
| Parameter | Unit | Value | Audit |
|---|
