Search by VIN, brand, model, type of equipment or unit name, by article of any oil:
Oil for Case - IH - Farmall C - Farmall 55C
Case - IH Farmall C Farmall 55C, year of issue from 2011 date to 2014 - Engine oil, automatic transmission, transmission oil, antifreeze, brake fluid, power steering fluid (power steering) and other fluids.
Fuel: Diesel fuel
car drive: All-wheel drive
Engine: Single row
Number of cylinders: 4
Valves per cylinder: 4
Working volume: 3200 cc
Power: 55 hp / 41 kW
Engine F5A
For mixed park
RAVENOL EURO IV Truck SAE 10W-40 is UHPD-Motoroil (Ultra High Performance Diesel) with special requirements for Diesel Particular Filters DPF for the LOW SPAsh Technology. Offers low content of sulphur, phosphor and low ash content.
Manufacturer Approved:
Deutz DQC IV-10 LA, DTFR 15C110, Mack EO-N, Renault RLD-2, Tatra TDS 30/12, Volvo VDS-3
Compliance with the requirements:
DAF HP-2, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RXD, Scania LDF
- Available packaging
- Product parameters
Volume:
1 L
vendor code:
1122107-001
Volume:
20 L, ecobox
vendor code:
1122107-B20
Volume:
1000 L
vendor code:
1122107-700
RAVENOL EURO IV Truck SAE 10W-40 is UHPD-Motoroil (Ultra High Performance Diesel) with special requirements for Diesel Particular Filters DPF for the LOW SPAsh Technology. Offers low content of sulphur, phosphor and low ash content.
Application Note
RAVENOL EURO IV Truck SAE 10W-40 is maximum efficiency engine oil which can be used the whole year and which was produced for the new exhaust gas emission directives respectively for vehicles with exhaust gas return systems.
RAVENOL EURO IV Truck SAE 10W-40 can be used in all diesel engines with and without turbo charging. Suitable for EURO I, II, III, IV and EURO V engines.
Characteristics
- High corrosion protection
- An excellent oxidation stability
- An excellent high temperature stability
- Excellent detergent and dispersant characteristics
- Profitability because of a low fuel consumption
- Long endurance because of a high oxidation stability
- An excellent cold start behaviour, a quick engine lubrication at low temperatures
- A very good viscosity temperature behaviour
- Neutrality of sealing
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Recommendations | DAF HP-2, MAN M 3277 (CRF Abgasrückführung), MAN M 3477, MB 228.51, MTU Typ 3, MTU Typ 3.1, Renault RXD, Scania LDF |
DAF HP-2, MAN M 3277 (CRF Abgasrückführung), MAN M 3477, MB 228.51, MTU Typ 3, MTU Typ 3.1, Renault RXD, Scania LDF
|
||
| SAE | 10W-40 |
10W-40
|
||
| Brand | RAVENOL |
RAVENOL
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | CI-4 |
CI-4
|
||
| ACEA | E6, E7 |
E6, E7
|
||
| Manufacturer Approved | Deutz DQC IV-10 LA, DTFR 15C110, Mack EO-N, Renault RLD-2, Tatra TDS 30/12, Volvo VDS-3 |
Deutz DQC IV-10 LA, DTFR 15C110, Mack EO-N, Renault RLD-2, Tatra TDS 30/12, Volvo VDS-3
|
||
| Recomendations | DAF HP-2, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RXD, Scania LDF |
DAF HP-2, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RXD, Scania LDF
|
||
| Density at 20 °C | g/cm³ | 856 | EN ISO 12185 |
856
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 14.7 | DIN 51562-1 |
14.7
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 99.3 | DIN 51562-1 |
99.3
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 153 | DIN ISO 2909 |
153
DIN ISO 2909
|
|
| HTHS Viscosity at 150 °C | mPa*s | 4.1 | ASTM D5481 |
4.1
mPa*s
ASTM D5481
|
| CCS Viscosity at -25 °C | mPa*s | 6600 | ASTM D5293 |
6600
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -30 °C | mPa*s | 19.700 | ASTM D4684 |
19.700
mPa*s
ASTM D4684
|
| Pourpoint | °C | -39 | DIN ISO 3016 |
-39
°C
DIN ISO 3016
|
| Noack Volatility | % | 6.7 | ASTM D5800 |
6.7
%
ASTM D5800
|
| Flashpoint | °C | 249 | DIN EN ISO 2592 |
249
°C
DIN EN ISO 2592
|
| tbn | mgKOH/g | 10.4 | ASTM D2896 |
10.4
mgKOH/g
ASTM D2896
|
| Sulphated Ash | %wt. | 0.87 | DIN 51575 |
0.87
%wt.
DIN 51575
|
| Approvals | DAF HP-2, Deutz DQC IV-10 LA, DTFR 15C110, Mack EO-N, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RLD-2, Renault RXD, Scania LDF, Tatra TDS 30/12, Volvo VDS-3 |
DAF HP-2, Deutz DQC IV-10 LA, DTFR 15C110, Mack EO-N, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RLD-2, Renault RXD, Scania LDF, Tatra TDS 30/12, Volvo VDS-3
|
For mixed fleet
RAVENOL Turbo plus SHPD SAE 15W-40 can be used for diesel and petrol engines, also with turbochargers.
Manufacturer Approved:
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, Deutz DQC III-10, DTFR 15B110, MTU Type 2, Renault RLD, Renault RLD-2, TEDOM 258-3, Volvo VDS-3
Compliance with the requirements:
Allison C-4, Caterpillar TO-2, Global DHD-1, John Deere JDQ-78 A, Mack EO-M, Mack EO-M Plus, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF-2, ZF TE-ML 07C
SAE: 15W-40
Equivalents OEM:
Alpine 0100323,
Alpine 100324,
Chrysler 68024966AA,
Chrysler 68024966PB,
Chrysler 68024966PD,
Chrysler 68024967AA,
Chrysler 68218940AA,
Chrysler 68218940AB,
Chrysler 68218940AC,
Chrysler 68218940AD,
Chrysler 68218940CB,
Chrysler 68218941AA,
Chrysler 68218941AB,
Chrysler 68218941AC,
Chrysler 68218941CB,
Chrysler 68218941CB,
Chrysler 68218942AA,
Chrysler 68218943AA,
Chrysler 68218943AD,
Chrysler 68218944AA,
FEBI 32925,
FEBI 32926,
FEBI 32927,
FEBI 32928,
FEBI 32929,
FEBI 32930,
Motorcraft XO15W40BSD,
Motorcraft XO15W40DSD,
Motorcraft XO15W40DSDR,
Motorcraft XO15W40QSD,
Motorcraft XO15W40QSD1
Alpine 0100323, Alpine 100324, Chrysler 68024966AA, Chrysler 68024966PB, Chrysler 68024966PD, Chrysler 68024967AA, Chrysler 68218940AA, Chrysler 68218940AB, Chrysler 68218940AC, Chrysler 68218940AD, Chrysler 68218940CB, Chrysler 68218941AA, Chrysler 68218941AB, Chrysler 68218941AC, Chrysler 68218941CB, Chrysler 68218941CB, Chrysler 68218942AA, Chrysler 68218943AA, Chrysler 68218943AD, Chrysler 68218944AA, FEBI 32925, FEBI 32926, FEBI 32927, FEBI 32928, FEBI 32929, FEBI 32930, Motorcraft XO15W40BSD, Motorcraft XO15W40DSD, Motorcraft XO15W40DSDR, Motorcraft XO15W40QSD, Motorcraft XO15W40QSD1, Motorcraft XO15W40QSDF, Motorcraft XO15W40QSDW, Motorcraft XO15W40TBSD, Motorcraft XO15W405Q3SD, Motorcraft XO15W405QSD, Motorcraft XO15W406GSD, SWAG 15932925, SWAG 15932926, SWAG 15932927, SWAG 15932928, SWAG 15932929, SWAG 15932930, Toyota 0888080805, Toyota 0888080806, Volvo 85102464
- Available packaging
- Product parameters
Volume:
1 L
vendor code:
1123115-001
Volume:
4 L
vendor code:
1123115-004
Volume:
7 L
vendor code:
1123115-007
Volume:
1000 L
vendor code:
1123115-700
RAVENOL Turbo plus SHPD SAE 15W-40 can be used for diesel and petrol engines, also with turbochargers.
RAVENOL Turbo plus SHPD SAE 15W-40 has been especially developed for extended oil change intervals, according to manufacturer’s recommendations.
Application Note
RAVENOL Turbo-Plus SHPD SAE 15W-40 is recommended by the engine manufacturers for extended oil change intervals as SAE 15W-40 multigrade engine oil in heavy duty commercial vehicle diesel engines.
RAVENOL Turbo-Plus SHPD SAE 15W-40 is the preferred use for extended oil life in turbo charged diesel engines according to manufacturer’s recommendations.
Characteristics
- Extremely high pressure absorption capacity
- Very high oxidation stability
- Excellent aging stability
- Excellent viscosity and temperature behaviour
- High security reserves even under limited lubrication circumstances
- Suitable for extended oil change intervals
- Suitable for heavy operating conditions
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Recommendations | Allison C4, Caterpillar TO-2, Global DHD-1, IVECO, JASO DH-1, John Deere JDQ-78A, Mack EO-M, Mack EO-M Plus, MAN M 3275-1 (Multigrades), MB 228.3, MB 229.1, Scania LDF-2, ZF TE-ML 07C |
Allison C4, Caterpillar TO-2, Global DHD-1, IVECO, JASO DH-1, John Deere JDQ-78A, Mack EO-M, Mack EO-M Plus, MAN M 3275-1 (Multigrades), MB 228.3, MB 229.1, Scania LDF-2, ZF TE-ML 07C
|
||
| SAE | 15W-40 |
15W-40
|
||
| Brand | RAVENOL |
RAVENOL
|
||
| Type | Mineral |
Mineral
|
||
| API | CI-4, SL |
CI-4, SL
|
||
| ACEA | A3, B4, E7 |
A3, B4, E7
|
||
| JASO | DH-1 |
DH-1
|
||
| Manufacturer Approved | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, Deutz DQC III-10, DTFR 15B110, MTU Type 2, Renault RLD, Renault RLD-2, TEDOM 258-3, Volvo VDS-3 |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, Deutz DQC III-10, DTFR 15B110, MTU Type 2, Renault RLD, Renault RLD-2, TEDOM 258-3, Volvo VDS-3
|
||
| Recomendations | Allison C-4, Caterpillar TO-2, Global DHD-1, John Deere JDQ-78 A, Mack EO-M, Mack EO-M Plus, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF-2, ZF TE-ML 07C |
Allison C-4, Caterpillar TO-2, Global DHD-1, John Deere JDQ-78 A, Mack EO-M, Mack EO-M Plus, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF-2, ZF TE-ML 07C
|
||
| Suitable for | IVECO, Steyr Motor GAZ 560, YaMZ |
IVECO, Steyr Motor GAZ 560, YaMZ
|
||
| Density at 20 °C | g/cm³ | 870 | EN ISO 12185 |
870
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 15 | DIN 51562-1 |
15
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 115.7 | DIN 51562-1 |
115.7
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 134 | DIN ISO 2909 |
134
DIN ISO 2909
|
|
| HTHS Viscosity at 150 °C | mPa*s | 4 | ASTM D5481 |
4
mPa*s
ASTM D5481
|
| Pourpoint | °C | -36 | DIN ISO 3016 |
-36
°C
DIN ISO 3016
|
| Flashpoint | °C | 238 | DIN EN ISO 2592 |
238
°C
DIN EN ISO 2592
|
| tbn | mgKOH/g | 10.5 | ASTM D2896 |
10.5
mgKOH/g
ASTM D2896
|
| Approvals | Allison C-4, Caterpillar TO-2, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, Deutz DQC III-10, DTFR 15B110, Global DHD-1, John Deere JDQ-78 A, Mack EO-M, Mack EO-M Plus, MAN M 3275-1, MB 228.3, MB 229.1, MTU Type 2, Renault RLD, Renault RLD-2, Scania LDF-2, TEDOM 258-3, Volvo VDS-3, ZF TE-ML 07C |
Allison C-4, Caterpillar TO-2, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, Deutz DQC III-10, DTFR 15B110, Global DHD-1, John Deere JDQ-78 A, Mack EO-M, Mack EO-M Plus, MAN M 3275-1, MB 228.3, MB 229.1, MTU Type 2, Renault RLD, Renault RLD-2, Scania LDF-2, TEDOM 258-3, Volvo VDS-3, ZF TE-ML 07C
|
Wheel reducers in front
Getriebeol UTTO Arctic
For tractors
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
Transmission in a unit with transmission/hydraulic system PowerShuttle
Getriebeol UTTO Arctic
For tractors
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
Transmission in a unit with transmission/hydraulic system SynchroShuttle
Getriebeol UTTO Arctic
For tractors
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
Differential, front
Getriebeol UTTO Arctic
For tractors
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
Hydraulic brake system
For brake system
Due to its special formulation RAVENOL LHM PLUS Fluid has significantly improved low temperature viscosity and fulfils the PSA approval specification.
- Available packaging
- Product parameters
Volume:
4 L
vendor code:
1181110-004
Volume:
20 L
vendor code:
1181110-020
Volume:
20 L, ecobox
vendor code:
1181110-B20
Volume:
1000 L
vendor code:
1181110-700
Due to its special formulation RAVENOL LHM PLUS Fluid has significantly improved low temperature viscosity and fulfils the PSA approval specification.
Application Note
RAVENOL LHM PLUS Fluid is used in vehicles with appropriately marked fluid reservoir for the hydraulic operation or support of braking, steering and suspension functions.
RAVENOL LHM PLUS Fuid is miscible with earlier LHM fluids.
Characteristics
- A low pour point.
- Excellent viscosity behavior at low temperatures.
- An extremely high viscosity index.
- Low viscosity at low temperatures.
- Neutral behavior towards sealing materials.
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| specification | ISO 7308, PSA B71 2710 |
ISO 7308, PSA B71 2710
|
||
| Density at 20 °C | g/cm³ | 831 | EN ISO 12185 |
831
g/cm³
EN ISO 12185
|
| Color | Green | visual |
Green
visual
|
|
| Viscosity at 100 °C | mm²/s | 7.2 | DIN 51562-1 |
7.2
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 25.3 | DIN 51562-1 |
25.3
mm²/s
DIN 51562-1
|
| Viscosity at -40 °C | 2600 | ASTM D445 |
2600
ASTM D445
|
|
| Viscosity Index VI | 273 | DIN ISO 2909 |
273
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 3460 | ASTM D2983 |
3460
mPa*s
ASTM D2983
|
| Pourpoint | °C | -72 | DIN ISO 3016 |
-72
°C
DIN ISO 3016
|
| Flashpoint | °C | 172 | DIN EN ISO 2592 |
172
°C
DIN EN ISO 2592
|
| Approvals | ISO 7308, PSA B71 2710 |
ISO 7308, PSA B71 2710
|
Lubrication points oilers
For bearings
RAVENOL Super EP-Langzeitfett is due to its smooth structure is easily conveyed.
Manufacturer Approved:
LOVAT LOV-204
- Available packaging
- Product parameters
RAVENOL Super EP-Langzeitfett is due to its smooth structure is easily conveyed.
RAVENOL Super EP-Langzeitfett is based on high-quality base oil by using lithium soaps (Li-12-hydroxy stearate) as thickener.
Due to this they avail of an outstanding work resistance. Futhermore, RAVENOL Super EP-Langzeitfett contain additives to improve the rust and corrosion-preventing behaviour.
Application Note
RAVENOL Super EP-Langzeitfett is used for the lubrication of heavily loaded plain and rolling bearings under the influence of moisture, vibration and shock loads. The standard applies to the lubrication of chassis, wheel bearings and universal joints in the automotive sector as well as machinery and general industry, construction industry, agriculture.
Characteristics
- Universal application, multi-purpose mixed pattern for machinery
- Excellent impact and wear-EP
- Very good oxidation and corrosion protection even in the presence of moisture
- Very good mechanical stability
- Excellent water resistance
- Long service life and thus extended lubrication intervals possible
- Very good resistance to aging
- Good pumpability, even at low temperatures
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
||
| Type | Mineral |
Mineral
|
||
| Manufacturer Approved | LOVAT LOV-204 |
LOVAT LOV-204
|
||
| specification | DIN 51502 KP2K-30, ISO I6743-9: ISO-L-XCCFB2 |
DIN 51502 KP2K-30, ISO I6743-9: ISO-L-XCCFB2
|
||
| Color | Brown | visual |
Brown
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KP2K-30 | DIN 51502 |
KP2K-30
DIN 51502
|
|
| Working Temperature | °C | -30 / +120 | DIN 51825 |
-30 / +120
°C
DIN 51825
|
| Short term temperature up to | °C | 130 | DIN 51757 |
130
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Dropping Point | °C | 180 — | DIN ISO 2176 |
180 —
°C
DIN ISO 2176
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| VKA Pressure Carrying Capacity | N | 2400 — 2600 | DIN 51350-4 |
2400 — 2600
N
DIN 51350-4
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 130 | DIN 51562-1 |
130
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KP2K-30, ISO I6743-9: ISO-L-XCCFB2, LOVAT LOV-204 |
DIN 51502 KP2K-30, ISO I6743-9: ISO-L-XCCFB2, LOVAT LOV-204
|
For bearings
Application NoteRAVENOL Hot Red Grease HRG 2 is used for the lubrication of roller and friction bearings under extreme pressure at high bearing temperatures.
Manufacturer Approved:
MAN 284 Li-H2, MB-Approval 265.1
Equivalents OEM:
BMW 83190447919, Land Rover STC3435, SWAG 10921909, VAG G052133A2, VAG G052133A2
- Available packaging
- Product parameters
Application Note
RAVENOL Hot Red Grease HRG 2 is used for the lubrication of roller and friction bearings under extreme pressure at high bearing temperatures.
RAVENOL Hot Red Grease HRG 2 is particularly recommended for the lubrication of commercial vehicles and for high-speed passenger car wheel bearings.
Characteristics
- Work resistance
- Resistance to oxidation
- Water resistance
- Good corrosion protection characteristics
- High thermal load capacity
- High pressure susceptibility
- Good adhesion
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
||
| Manufacturer Approved | MAN 284 Li-H2, MB-Approval 265.1 |
MAN 284 Li-H2, MB-Approval 265.1
|
||
| specification | DIN 51502 KP2P-35, ISO 6743-9: ISO-L-XCEEB2 |
DIN 51502 KP2P-35, ISO 6743-9: ISO-L-XCEEB2
|
||
| Color | Red | visual |
Red
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KP2P-35 | DIN 51502 |
KP2P-35
DIN 51502
|
|
| Working Temperature | °C | -35 / +160 | DIN 51825 |
-35 / +160
°C
DIN 51825
|
| Short term temperature up to | °C | 200 | DIN 51757 |
200
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Dropping Point | °C | 260 — | DIN ISO 2176 |
260 —
°C
DIN ISO 2176
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| VKA Pressure Carrying Capacity | N | 2600 — 2800 | DIN 51350-4 |
2600 — 2800
N
DIN 51350-4
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 140 | DIN 51562-1 |
140
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KP2P-35, ISO 6743-9: ISO-L-XCEEB2, MAN 284 Li-H2, MB 265.1 |
DIN 51502 KP2P-35, ISO 6743-9: ISO-L-XCEEB2, MAN 284 Li-H2, MB 265.1
|
For bearings
RAVENOL Arctic Green Grease AGG 2 offers excellent working resistance, rust and corrosion protection.
- Available packaging
- Product parameters
Volume:
200 g
vendor code:
1340126-200
Volume:
1 kg
vendor code:
1340126-001
Volume:
180 kg
vendor code:
1340126-180
RAVENOL Arctic Green Grease AGG 2 offers excellent working resistance, rust and corrosion protection.
Application for the lubrication of roller and friction bearings under extreme pressure at extremely low temperatures. Selected additives help reduce wear, even during severe continuous operation and significantly prolong the service life.
Application Note
RAVENOL Arctic Green Grease AGG 2 is used in roller and friction bearings under extreme pressure at extremely low temperatures.
The highest application temperature for RAVENOL Arctic Green Grease AGG 2 in continuous operation is 120°C. Peak performances of 160°C should not be exceeded.
Extremely high temperatures shorten the service life. Routine relubrication preserves material and saves costs.
Characteristics
- Working resistance
- Oxidation resistance
- Water resistance
- Good corrosion protection characteristics
- High thermal load capacity
- High pressure susceptibility
- Good adhesion
| Parameter | Unit | Value | Audit | |
|---|---|---|---|---|
| Brand | RAVENOL |
RAVENOL
|
||
| Type | Full synthetic |
Full synthetic
|
||
| specification | DIN 51502 KPE2K-60, ISO 6743-9: ISO-L-XECEB2 |
DIN 51502 KPE2K-60, ISO 6743-9: ISO-L-XECEB2
|
||
| Color | Green | visual |
Green
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KPE2K-60 | DIN 51502 |
KPE2K-60
DIN 51502
|
|
| Working Temperature | °C | -60 / +120 | DIN 51825 |
-60 / +120
°C
DIN 51825
|
| Short term temperature up to | °C | 160 | DIN 51757 |
160
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Dropping Point | °C | 180 — | DIN ISO 2176 |
180 —
°C
DIN ISO 2176
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| VKA Pressure Carrying Capacity | N | 3000 — 3200 | DIN 51350-4 |
3000 — 3200
N
DIN 51350-4
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 20 | DIN 51562-1 |
20
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KPE2K-60, ISO 6743-9: ISO-L-XECEB2 |
DIN 51502 KPE2K-60, ISO 6743-9: ISO-L-XECEB2
|
